AUX E&H Series Instrukcje Operacyjne Strona 20
- Strona / 92
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
4.3 Keys
CAL key
When the CAL key is pressed, the instrument prompts for the calibration
access code:
Code 22 for calibration
Code 0 or any code for calibration data checking.
Press the CAL key to acknowledge the calibration data or to proceed
within the calibration menu.
ENTER key
The ENTER key has serveral functions:
Opens the Setup menu in measuring mode
Stores (acknowledges) data entered in Setup mode
Moving on within the function groups.
PLUS key and MINUS key
The PLUS and MINUS keys have the following functions:
Selection of function groups
Setting of parameters and numeric values
Relay operation in manual mode (see Ch. 4.4).
Pressing the PLUS key allows you to switch between the current input
in % and mA.
Repeatedly pressing the PLUS key displays the following settings in
sequence as secondary measured values:
1. Temperature display in °F
2. Hide temperature display
3. Measured value display in mV
4. Current input signal in %
5. Current input signal in mA
6. Back to basic setting
Repeatedly pressing the MINUS key outputs errors:
1. The current errors are displayed one after the other (max. 10)
2. After all the errors are displayed, the standard display is unhidden.
In function group F, you can define an alarm for each error code
separately.
REL key
The REL key toggles between the relay and manual cleaning start in
manual mode. In automatic mode you can output the corresponding
switch-on points (limit contactor) ot set points (PID controller) when
pressing the REL key. Pressing the PLUS key allows you to display the
settings of the following relay. Press the REL key to return to measuring
mode (automatic return after 30s).
AUTO key
The AUTO key is used to toggle between the automatic and manual
modes of operation.
Escape function
Press the PLUS and MINUS keys simultaneously to return to the main
menu. Press the PLUS and MINUS keys again to return to measuring
mode.
Locking the keypad
Pressing the PLUS and ENTER keys simultaneously for minimum 3s
locks the keypad against unintentional entries. However, all settings can
still be read. The code prompt displays the code 9999.
Unlocking the keypad
Pressing the CAL and MINUS keys simultaneously for minimum 3s
unlocks the keypad. The code prompt displays the code 0:
Operation Liquisys M CPM 223 / 253
18 Endress+Hauser
- Endress Hauser 1
- Table of contents 3
- 1 General information 4
- 1.5 Product structure 5
- 2 Safety 6
- 2.5 Immunity to interference 7
- 2.6 Declaration of conformity 7
- 3 Installation 8
- 3.2 Dimensions 9
- 3.3 Mounting 10
- PM253E03.CHP 11
- 3.3.2 Mounting examples 12
- Endress+Hauser 11 13
- 3.4 Electrical connection 14
- 131094-4G 15
- Construction of special 16
- CPK1_12e.EPS 16
- Fig. 3.13 16
- • If the software setting 18
- Setpoint 19
- 4.3 Keys 20
- PM253ED4.CHP 21
- 4.5 Operating concept 22
- 4.5.2 Access codes 23
- 4.5.3 Menu structure 23
- • If a change is made but not 23
- • See the appendix of these 23
- 5 Instrument configuration 25
- RELAY2.CDR 26
- Oper.Mode 27
- Glass A5 28
- Fig. 5.4 29
- Alarm signalling and 29
- 28 Endress+Hauser 30
- PM253E5A.CHP 31
- Fig. 5.7 32
- User-defined current output 32
- Sel. Out2 33
- Tabelle (3) 34
- Table (3) 34
- 5.5 Monitoring functions 35
- Rel.Assg 36
- Curr.Assg 36
- CleanTrig 36
- 5.5.2 Check 37
- • Due to its semiconductor 37
- A.Thresh 38
- Err.Delay 38
- LowAlarm 38
- HighAlarm 39
- ProcMonit 39
- Tmax Low 39
- Tmax High 39
- GRENZ-E.CDR 40
- not allowed 41
- Pulse length modulation 42
- Pulse frequency modulation 42
- PM253E5B.CHP 43
- 5.6.4 ChemoClean function 44
- • Use relays 3 (water) and 44
- • When “Economy” is selected 44
- LC PV R2 45
- LC State 46
- 120 R239 48
- 0.3 R2310 48
- Clean = ChemoClean (5) 49
- Neutra controller (6) 49
- ChemoClean (5) 49
- Proc.Type 51
- 5.7 Service 52
- S.Default 53
- Contr E1 54
- SerNo E113 54
- LSG E114 54
- 5.10 Calibration 55
- the user is 55
- ≤ 0.05 and value 56
- 59.18 N2 59
- PV Offset 60
- 6 Interfaces 61
- Endress+Hauser 61 63
- 62 Endress+Hauser 64
- Endress+Hauser 63 65
- 64 Endress+Hauser 66
- Endress+Hauser 65 67
- 8.1 Diagnosis 68
- Endress+Hauser 67 69
- 223EXPHE.CDR 70
- 8.2.2 Disassembly of CPM 223 71
- 8.2.3 Assembly of CPM 223 71
- 8.2.4 Spare parts for CPM 223 72
- 253EXPHE.CDR 73
- 8.3.2 Disassembly of CPM 253 74
- 8.3.3 Assembly of CPM 253 74
- 8.3.4 Spare parts for CPM 253 75
- 8.4 Spare parts orders 76
- 8.6.1 pH/redox transmitter 77
- 8.6.2 pH/mV electrodes 77
- 8.6.3 Assembly 77
- 8.6.4 Liquid KCl supply 77
- 9 Accessories 79
- 10 Technical data 81
- 80 Endress+Hauser 82
- Endress+Hauser 81 83
- 11 Appendix 84
- Endress+Hauser 83 85
- 84 Endress+Hauser 86
- Endress+Hauser 85 87
- 12 Index 88
- PM253E12.CHP 89
- Declaration of contamination 91
- BA 194C/07/en/07.02 92
- Printed in Germany / CV5 / DT 92
Powiązane produkty i podręczniki dla Klimatyzatory typu split AUX E&H Series
(15 strony)
(19 strony)
(2 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji